Quick answer
Correct installation of the charging station and boundary wire is essential for your robot mower to work correctly.
An incorrectly positioned charging station or boundary wire can cause issues such as:
- The mower not returning to the charging station
- The mower leaving the mowing area
- The mower not detecting the boundary correctly
- Charging problems
Follow the steps below to correctly install your robot mower charging station and boundary wire.
Before you begin
Before installing the boundary wire and charging station, make sure you have:
- A suitable flat area of lawn for the charging station
- Enough boundary wire to cover your mowing area
- The fixing pegs supplied with your mower
- Access to a power socket for the charging station
Before securing anything permanently, plan the layout of your garden and check the position of the charging station.
AMIRO 400/400i
X series set up video
Planning and installing video for ECO, H, and Pro series
Steps
1. Choose the charging station location
The charging station should be positioned carefully to allow the robot mower to leave and return correctly.
Make sure the charging station:
- Is placed on flat, level ground
- Is positioned near the edge of the lawn
- Has a clear area around it with no obstacles
- Allows the boundary wire to connect easily
The robot mower may not dock correctly if the charging station is installed incorrectly.
Do not secure the charging station permanently until the boundary wire has been installed underneath it.
2. Install the boundary wire
Before installing the wire, plan where the mowing area boundary will be.
The boundary wire should:
- Be positioned approximately 40cm from the edge of the lawn
- Create a clear mowing area for the robot mower
- Be secured using the supplied fixing pegs
Install the wire around the perimeter of your lawn, ensuring it sits flat against the ground.
3. Connect the boundary wire to the charging station
The boundary wire connects to two points on the back of the charging station.
Front section of boundary wire
The wire approaching the charging station from the front should:
- Run underneath the charging station.
- Continue in a straight line towards the rear of the station.
- Connect to the terminal marked “F”.
To connect the wire:
- Strip approximately 10-15mm of insulation from the wire.
- Twist the exposed wire strands together.
- Insert the wire into the connector.
Return section of boundary wire
The other end of the boundary wire should:
- Loop around the mowing area.
- Return to the charging station.
- Connect to the terminal marked “B”.
Repeat the same process to expose enough wire for the connector if required.
4. Check the boundary wire layout
Before securing the installation, check the following:
- There should be at least 2 metres of straight boundary wire in front of the charging station.
- Avoid sharp corners or angles less than 120°.
- The total boundary wire length must not exceed 300 metres.
- Any spare wire should be placed outside the mowing area and underneath the charging station.
Do not coil excess wire, as this may affect the signal.
5. Secure the charging station
Once the boundary wire has been correctly positioned:
- Place the charging station in its final position.
- Secure it using the four supplied fixing pegs.
- Connect the charging station to the mains power supply.
The charging station LED will indicate the boundary wire status:
- S1 or S2 LED illuminated: Installation is working correctly.
- LED flashing: The boundary wire may be broken, disconnected, or incorrectly installed.
Frequently Asked Questions
How far should the boundary wire be from the edge of the lawn?
The boundary wire should normally be positioned around 40cm from the edge of the lawn to allow the mower to cut effectively while staying within the mowing area.
Why is my robot mower not returning to the charging station?
This can be caused by an incorrectly installed boundary wire or charging station. Check that the wire is straight in front of and underneath the charging station and that the station is positioned correctly.
How much space should be left in front of the charging station?
Leave at least 2 metres of straight boundary wire in front of the charging station to allow the mower enough space to approach and dock.
Can I use more than 300 metres of boundary wire?
No. The total boundary wire length should not exceed 300 metres.
Why is the charging station LED flashing?
A flashing LED usually indicates a problem with the boundary wire. Check the wire for breaks, loose connections, or incorrect installation.
Can I roll up spare boundary wire?
No. Excess wire should not be rolled up, as this can interfere with the boundary signal. Place spare wire underneath the charging station and outside the mowing area.
If you continue to experience issues after checking the boundary wire and charging station setup, contact our support team through live chat for further assistance.